# DFNT.CFG (File name specific!!! Must be named DFNT.CFG when downloading # to the MVI46-DFNT) # # This file contains the configuration for the MVI46-DFNT communication # module. # # LOCATION : # DATE : 06/12/2007 # CONFIGURED BY : # MODIFIED : # # This section is used to define the configuration for the Module level # data. # [Module] Module Name : Test Example of MVI46-DFNT Communication Module M1 Write Size : 4000 #0-4000 words transferred between SLC and MVI Failure Flag Count : 0 #Determines if BP failure will cause protocol to be #disabled (0=Ignore, >0 = failure count to disable) Initialize Output Data : No #Initialize the database file on startup DFNT Server File Size : 100 #100 or 1000 as max file size for DFNT server Float Write Start : 1000 #Word reg for float write data for swapping multiple of 50 Float Write Count : 50 #muliple of 50 for MVI46 # This section is used to define the DF1 pass-through server on Port 0 [DF1 Pass-Through Server Port 1] Enabled : No #Y=Use server, N=Do not use server Service Port Number : 15000 #TCP service port for this server Busy Timeout : 500 #Time to wait for not Busy (100-65535 mSec) Baud Rate : 19200 #Baud rate for port 110-115200 Parity : None #N=None,O=Odd,E=Even,M=Mark,S=Space Data Bits : 8 #5, 6, 7 or 8 Stop Bits : 1 #1 or 2 RTS On : 0 #0-65536 mSec before message RTS Off : 0 #0-65536 mSec after message Use CTS Line : No #Use CTS modem control line (Y/N) # This section is used to define the configuration for the DF1 pass-through # port on the Debug/Configuration port # [DF1 Pass-Through Port] Enabled : No #Y=Use port, N=Do not use port Local Station ID : 1 #DF1 node address Protocol : Full #F=Full-Duplex, H=Half-Duplex Termination Type : CRC #B=BCC, C=CRC Baud Rate : 576 #Baud rate for port 110-115200 Parity : None #N=None,O=Odd,E=Even,M=Mark,S=Space Data Bits : 8 #5, 6, 7 or 8 Stop Bits : 1 #1 or 2 RTS On : 0 #0-65536 mSec before message RTS Off : 0 #0-65536 mSec after message Use CTS Line : No #Use CTS modem control line (Y/N) Retry Count : 3 #Response failure retry count Request Timeout : 1000 #Request messgage timeout (0-65535 mSec) Busy Timeout : 500 #Port Busy timeout (0-65535 mSec) ACK Timeout : 100 #DLE-ACK timeout (0-65535 mSec) # This section is used to define the configuration for the master device # simulated on network port # [DFNT Client 0] Minimum Command Delay : 0 #Minimum number of msec's between commands Response Timeout : 1000 #Response messgage timeout (0-65535 mSec) Retry Count : 0 #Response failure retry count [DFNT Client 0 Commands] # # The file contains examples for a ControlLogix processor with the N7 file # configured. This example uses SLC and PLC5 commands. # # LOCATION : # DATE : 04/05/2000 # CONFIGURED BY : RAR # MODIFIED : # # 1 2 3 4 5 6 7 8 9 10 11 12 # DB Poll Swap Func File File Elm Sub #Enab Addr Delay Count Code Node IP Address Slot Code Type # # Elm START # 1 0 0 10 0 192.168.0.101 -1 501 N 11 0 # 1 10 0 10 0 192.168.0.101 -1 509 N 12 0 # 1 20 0 10 0 192.168.0.101 -1 502 N 13 0 0 # 1 30 0 10 0 192.168.0.101 -1 510 N 14 0 0 # # DB Poll Swap Func File Elm Sub #Enab Addr Delay Count Code Node IP Address Slot Code # # Elm # 1 40 0 10 0 192.168.0.102 -1 101 7 0 0 END