# BARDACDW.CFG # # This is an example configuration file for the MVI56-BARDAC-DW module. # # COMPANY : # DATE : # LOCATION : # # # This section of the file describes the database setup and module level # parameters. # [Module] Module Name : MVI56-BARDAC-DW Communication Module Test #Password : PASSWORD Local Domain Name : vcs.com Error/Status Pointer : 3000 #Database location for module level status data Read Register Start : 0 #Starting DB address where read data stored Read Register Count : 600 #Number of regs to read from processor Write Register Start : 600 #Starting DB address where write data accessed Write Register Count : 600 #Number of regs to write to processor Failure Flag Count : 0 #Determines if BP failure will cause protocol to be #disabled (0=Ignore, >0 = failure count to disable) Initialize Output Data : 0 #Read output values from controller (0=No or 1=Yes) # This section is used to define the configuration for the master device # simulated on Bardac DW UDP service port 48556 (0xBDAC) # [Bardac DW Client 0] Error/Status Pointer : 4000 #Database offset for client status data Command Error Pointer : 4010 #Database offset for client command error list Minimum Command Delay : 20 #Minimum number of msec's between commands Response Timeout : 1000 #Response messgage timeout (0-65535 mSec) Retry Count : 0 #Response failure retry count [Bardac DW Client 0 Commands] # # This section contains examples for a Bardac DW UDP/IP client using service port # 48556 (0xBDAC). Refer to the drive documentation for a full list of Parameter # ID's. This section can contain up to 100 commands. # # 1 2 3 4 5 6 7 8 # DB Poll Swap Cmd Parameter #Enab Addr Delay Code Node IP Address Code ID START # # This is a set of GET instructions 1 110 0 0 192.168.0.67 0 296 1 111 0 0 192.168.0.67 0 181 1 112 0 0 192.168.0.67 0 180 1 113 0 0 192.168.0.67 0 179 1 114 0 0 192.168.0.67 0 178 1 115 0 0 192.168.0.67 0 171 1 116 0 0 192.168.0.67 0 172 1 117 0 0 192.168.0.67 0 173 1 118 0 0 192.168.0.67 0 174 1 119 0 0 192.168.0.67 0 175 # # This is a set of SET instructions (disabled as default) 0 0 0 0 192.168.0.67 1 281 0 1 0 0 192.168.0.67 1 282 0 2 0 0 192.168.0.67 1 250 0 3 0 0 192.168.0.67 1 251 0 4 0 0 192.168.0.67 1 252 0 5 0 0 192.168.0.67 1 253 0 6 0 0 192.168.0.67 1 254 END # This section is used to define the configuration for the master device # simulated on Bardac DW UDP service port 48556 (0xBDAC) # [Bardac DW Client 1] Error/Status Pointer : 4100 #Database offset for client status data Command Error Pointer : 4110 #Database offset for client command error list Minimum Command Delay : 20 #Minimum number of msec's between commands Response Timeout : 1000 #Response messgage timeout (0-65535 mSec) Retry Count : 0 #Response failure retry count [Bardac DW Client 1 Commands] # # This section contains examples for a Bardac DW UDP/IP client using service port # 48556 (0xBDAC). Refer to the drive documentation for a full list of Parameter # ID's. This section can contain up to 100 commands. # # 1 2 3 4 5 6 7 8 # DB Poll Swap Cmd Parameter #Enab Addr Delay Code Node IP Address Code ID START # # This is a set of GET instructions for testing 1 140 0 0 192.168.0.67 0 296 1 141 0 0 192.168.0.67 0 181 1 142 0 0 192.168.0.67 0 180 1 143 0 0 192.168.0.67 0 179 END # This section is used to define the configuration for the master device # simulated on Bardac DW UDP service port 48556 (0xBDAC) # [Bardac DW Client 2] Error/Status Pointer : 4200 #Database offset for client status data Command Error Pointer : 4210 #Database offset for client command error list Minimum Command Delay : 20 #Minimum number of msec's between commands Response Timeout : 1000 #Response messgage timeout (0-65535 mSec) Retry Count : 0 #Response failure retry count [Bardac DW Client 2 Commands] # # This section contains examples for a Bardac DW UDP/IP client using service port # 48556 (0xBDAC). Refer to the drive documentation for a full list of Parameter # ID's. This section can contain up to 100 commands. # # 1 2 3 4 5 6 7 8 # DB Poll Swap Cmd Parameter #Enab Addr Delay Code Node IP Address Code ID START # # This is a set of GET instructions for testing 1 150 0 0 192.168.0.67 0 296 1 151 0 0 192.168.0.67 0 181 1 152 0 0 192.168.0.67 0 180 1 153 0 0 192.168.0.67 0 179 END # This section is used to define the configuration for the master device # simulated on Bardac DW UDP service port 48556 (0xBDAC) # [Bardac DW Client 3] Error/Status Pointer : 4300 #Database offset for client status data Command Error Pointer : 4310 #Database offset for client command error list Minimum Command Delay : 20 #Minimum number of msec's between commands Response Timeout : 1000 #Response messgage timeout (0-65535 mSec) Retry Count : 0 #Response failure retry count [Bardac DW Client 3 Commands] # # This section contains examples for a Bardac DW UDP/IP client using service port # 48556 (0xBDAC). Refer to the drive documentation for a full list of Parameter # ID's. This section can contain up to 100 commands. # # 1 2 3 4 5 6 7 8 # DB Poll Swap Cmd Parameter #Enab Addr Delay Code Node IP Address Code ID START # # This is a set of GET instructions for testing 1 160 0 0 192.168.0.67 0 296 1 161 0 0 192.168.0.67 0 181 1 162 0 0 192.168.0.67 0 180 1 163 0 0 192.168.0.67 0 179 1 170 0 0 192.168.0.67 0 296 1 171 0 0 192.168.0.67 0 181 1 172 0 0 192.168.0.67 0 180 1 173 0 0 192.168.0.67 0 179 END # This section is used to define e-mail reports to be sent from the module # to a specified e-mail server/user account based on the value of selected # user register/value combinations. When the specified register value contains # the value defined, the e-mail file will be sent from the module. [E-MAIL] # DB Trigger Mail TO # Reg Value Server IP Name E-Mail File Name START 0 1000 192.168.0.61 rich@vcs.com stat END