# DFNT.CFG
#
# This file contains the configuration for the MVIxx-DFNT communication
# module.
#
# LOCATION      :
# DATE          :
# CONFIGURED BY :
# MODIFIED      :
#
# This section is used to define the configuration for the Module level
# data.
#
[Module]
Module Name : Test Example of MVI71-DFNT Communication Module

Read Register Start  :    0 #First register to transfer from module -> PLC
Read Register Count  :  120 #Number of registers to transfer to PLC
Write Register Start :  200 #First register where to store data received from PLC
Write Register Count :  120 #Number of registers to receive from PLC

Failure Flag Count     :     -1 # Number of BP Errors to disable protocol comm 
Initialize Output Data :     No #Initialize the database file on startup
DFNT Server File Size  :    100 #100 or 1000 as max file size for DFNT server


# This section is used to define the DF1 pass-through server on Port 1
# (the second port)

[DF1 Pass-Through Server Port 1]
Enabled                 :   Yes  #Y=Use server, N=Do not use server
Service Port Number     : 15000  #TCP service port for this server
Busy Timeout            :   500  #Time to wait for not Busy (100-65535 mSec)
Baud Rate               : 19200  #Baud rate for port 110-19200
Parity                  :     N  #N=None,O=Odd,E=Even,M=Mark,S=Space
Data Bits               :     8  #5, 6, 7 or 8
Stop Bits               :     1  #1 or 2

# This section is used to define the configuration for the DF1 pass-through
# port on Port 2 (the third port)
#

[DF1 Pass-Through Port]
Enabled                 :    Y   #Y=Use port, N=Do not use port
Local Station ID        :    1   #DF1 node address
Protocol                :    H   #F=Full-Duplex, H=Half-Duplex
Termination Type        :  CRC   #B=BCC, C=CRC
Baud Rate               : 38400  #Baud rate for port 1200-38400
Parity                  : None   #N=None,O=Odd,E=Even,M=Mark,S=Space
Data Bits               :    8   #5, 6, 7 or 8
Stop Bits               :    1   #1 or 2
RTS On                  :    0   #0-65536 mSec before message
RTS Off                 :    0   #0-65536 mSec after message
Use CTS Line            :    N   #Use CTS modem control line (Y/N)

Retry Count             :    3   #Response failure retry count
Request Timeout         :  500   #Request messgage timeout (0-10000 mSec)
Busy Timeout            :  500   #Port Busy timeout (0-10000 mSec)
ACK Timeout             :  500   #DLE-ACK timeout (0-10000 mSec)


# This section is used to define the configuration for the master device
# simulated on network port
#
[DFNT Client 0]
Minimum Command Delay   :   30   #Minimum number of msec's between commands
Response Timeout        : 1000   #Response message timeout (0-5000 mSec)
Retry Count             :    3   #Response failure retry count


[DFNT Client 0 Commands]
#
# The file contains examples for a ControlLogix processor with the N7 file
# configured.  This example uses SLC and PLC5 commands.
#
# LOCATION      :
# DATE          : 04/05/2000
# CONFIGURED BY : RAR
# MODIFIED      :
#
#   1     2      3     4    5  6                  7    8    9   10   11   12
#        DB   Poll       Swap                       Func File File  Elm  Sub
#Enab  Addr  Delay Count Code  Node IP Address Slot Code Type    #    #  Elm
START
     1     0      0     5    0  192.168.0.136      0  501    N   10    0
     0   200      0     5    0  192.168.0.136      0  509    N   10    5
END