<?xml version="1.0"?>

<rss version="2.0">


<channel>
<title>Home - All Categories - Gateways  - AN-X  - AutoMax  </title>
<link>http://www.prosoft-technology.com/kb/category.php?id=137</link>
<description>This RSS Feed contains Articles of Category in the knowledge base. You can click on the title to view its content. Powered by PHPKB Knowledge Base Script (http://www.knowledgebase-script.com)</description>
<item>
										<guid>http://www.prosoft-technology.com/kb/article.php?id=531</guid>
										<title>What are the differences between the DCSNet and DCSNet2 firmware?</title>
										<link>http://www.prosoft-technology.com/kb/article.php?id=531</link>
										<description><![CDATA[The major difference between these 2 firmware revisions is how much data the AN-X-AMX unit can transfer to a CompactLogix or ControlLogix processor:   DCSNet firmware supports emulating a single Generic I/O module in RSLogix 5000 with a limit of 500...]]></description>

									</item>
<item>
										<guid>http://www.prosoft-technology.com/kb/article.php?id=532</guid>
										<title>When operating as a DCSNet(2) slave can the AN-X-AMX gateway be configured to emulate more than 1 drop area?</title>
										<link>http://www.prosoft-technology.com/kb/article.php?id=532</link>
										<description><![CDATA[The AN-X-AMX gateway can be configured to emulate multiple drops, but only in a single consecutive drop area.  For instance it is possible to configure the AN-X-AMX to be drop 40 - 47 by setting the Drop to 40 and the depth to 8.]]></description>

									</item>
<item>
										<guid>http://www.prosoft-technology.com/kb/article.php?id=513</guid>
										<title>Does the AN-X-AMX support RNET?</title>
										<link>http://www.prosoft-technology.com/kb/article.php?id=513</link>
										<description><![CDATA[The AN-X-AMX does not support the RNET protocol which was used on the old AutoMate 30 series processors.]]></description>

									</item>
<item>
										<guid>http://www.prosoft-technology.com/kb/article.php?id=535</guid>
										<title>Is it possible for a FactoryTalk View application to get data from a DCSNet(2) AN-X-AMX Slave?</title>
										<link>http://www.prosoft-technology.com/kb/article.php?id=535</link>
										<description><![CDATA[Yes,     To do so create an ethernet device by right clicking on EtherNet:  Browse the NET ENI folder Browse the PLC5 Folder Select the 2nd PLC5 in the list which is the PLC5 L40C When prompted enter the IP Address of the AN-X-AMX gateway  Map your...]]></description>

									</item>
<item>
										<guid>http://www.prosoft-technology.com/kb/article.php?id=534</guid>
										<title>What is the default addressing schema for the EtherNet IP DCSNet(2) Slave interface?</title>
										<link>http://www.prosoft-technology.com/kb/article.php?id=534</link>
										<description><![CDATA[When using the DCSNet(2) firmware in a slave configuration the addresses use the following layout:  Drop 0 = N100:0 - N100:63 Drop 1 = N101:0 - N101:63 Drop 2 = N102:0 - N102:63 etc....  The first 32 registers (0 - 31) contains the data that will be...]]></description>

									</item>

</channel>

</rss>