500mW 5.8GHz RF Amplifier
AMP58-500
The RadioLinx AMP58-500 Amplifier series are Automatic Gain Control (AGC) compensated for constant power output bi-directional amplification. This provides constant maximum output power at the antenna over a wide RF input range. An amplifier significantly improves the link reliability and operating range by low noise amplification in receive mode, and spectrally clean power amplification in transmit mode. This amplifier has unique internal filtering and AGC in both the Tx and Rx paths. This combination provides exceptional performance in high traffic areas.
The bi-directional amplifier may also be used if an application requires long lengths of coaxial cable to reach the antenna. The amplifier is designed to put maximum power right at the antenna and boost the received signal primarily to overcome cable loss and improve overall receiver signal quality. The AMP58-500 amplifier has been specifically FCC approved for use with RadioLinx radios.
Features and Benefits
- Automatic Gain Control (AGC)
- P1dB Compression Point = +32dBm (1.5W)
- OFDM 802.11a Power Output: +27dBm (500mW)
- Low 2.5dB RX Noise Figure
- Low Transmit Harmonics
- Ruggedly designed for outdoor use
- Internal Lightning Protection
- Machined Aluminum Housing
- 2 Year Warranty w/ Lightning Protection
Installation Guidelines
- Each AMP58-500 amplifier is equipped with internal ¼ wave technology lightning protection
- The AMP58-500 amplification device is a RadioLinx subassembly and its use has been FCC approved for use in an RF system. The AMP58-500 kit has been pre-designed to meet FCC approval and use under the following guidelines:
-
- The bi-directional amplifier has been designed to operate with a cable loss between the radio and amplifier of 6.5 dB to 20 dB. Within this range, the output of the amplifier will always be ½ W regardless of the input level
- The amplifier may not be used with less than 6.5 dB cable loss. With more than 20 dB of coaxial cable loss, the amplifier will not turn on
- Use of the amplifier outside of these guidelines will result in violation of 47 CFR Part 15 FCC Rules, under which the equipment has been authorized
Specifications
|
Frequency Coverage
|
5.47 to 5.825 GHz
|
|
Supply Voltage
|
+12 VDC +/- 5%
|
|
Receive
|
|
|
Gain
|
10 dB +/- 2dB
|
|
Noise Figure
|
2.5 dB
|
|
Supply Current
|
<250 mA
|
|
Tx to Rx Switching
|
< 500 nSec
|
|
Transmit:
|
|
|
AGC Power
|
Avg Power: 500 mW (27dBm), Pin +5 to +20 dBm
Peak Power 1500 mW (+32 dBm)
|
|
Compression Point
|
P1dBm = 1500 mW (+32dBm)
|
|
RF Input Power for Turn-On
|
>1 dBm
|
|
Harmonic Rejection
|
2fo > 55 dBc, 3fo >70dBc @ Po=+27dBm
|
|
Supply Current
|
< 1 A
|
|
Rx to Tx Switching
|
< 500 nSec
|
|
Maximum Ratings
|
Pin (Radio port) + 30 dBm
Pin (Antenna port) + 27 dBm
|
|
Size
|
2.88 in. x 3.00 in. x1.01 in.
|
|
Weight
|
< 12 oz.
|
|
Chassis
|
Machined Aluminum with durable black anodize finish
CCA is protected with a conformal coating compound
|
|
Indicator LED
|
Green LED - Rx mode, Red LED - Tx mode.
|
Ordering Information
| AMP58-500 |
500mW 5.8GHz RF Amplifier |
| |
|
| To place an order, please contact your local ProSoft Technology, Inc. distributor. For a list of ProSoft distributors near you, click here. |
Distributors:
Place your order by email to orders@prosoft-technology.com:, fax to +1 661-716-5101.
Sales and Support:
|
