| KB Home | Advanced Search | News | Ask Question |
|
| ProSoft Knowledge Base | |
|
Category Articles 
How to get your RadioLinx Industial Hotspots to link.
Viewed 1 times since Mon, Aug 3, 2015
Follow the simple steps to get your radios to link with the document attached. Read More
What is the maximum distance I can get out of the RLX-IH RadioLinx radio?
Viewed 1 times since Tue, Jan 23, 2007
In the US, with the correct antenna selection, and installation, 20 miles is very attainable. Read More
What is the Mean Time Between Failure (MTBF) for the RLX-IH modules?
Viewed 1 times since Tue, Nov 28, 2006
The RLX-IH module line is 2,190,000 hours. Read More
What is the affect of different materials blocking a RadioLinx RLX-IH signal?
Viewed 1 times since Tue, Nov 28, 2006
The increase in attenuation can be as high as 3DB. the following provides some examples of the attenuation values of common office construction: plasterboard wall 3db glass wall with metal frame 6db cinder block wall 4db office window 3db... Read More
After configuring a temporary IP address on the RLX-IH Radio, I can no longer access the radio over Ethernet
Viewed 1 times since Tue, Nov 28, 2006
This issue occurs when using temporary IP address and firewall. Disable the firewall then configure the IP address. Once the IP address is set, re-start the firewall. Read More
What components do I need for a wireless Ethernet network between ControlLogix and 1734 Point I/O PLCs?
Viewed 1 times since Mon, Sep 26, 2011
All of our Ethernet radios will function as transparent Ethernet bridge devices. We would recommend one of our "Industrial Hotspot" radios" RLXIB-IHW: 802.11a/b/g Industrial Hotspot RLXIB-IHA: 802.11a Industrial Hotspot RLXIB-IHG: 802.11g... Read More
What kind of security and encryption do the Industrial Hotspots offer?
Viewed 1 times since Mon, Oct 19, 2015
This unit supports both “Personal” and “Enterprise” security modes as well as Legacy WEB encryption modes for interoperability with legacy devices. The following security mode settings are supported: - None – Not recommended. - Personal ... Read More
My RLXIB-IHW radio does not seemed to be working at 5GHz. How do I fix it?
Viewed 1 times since Fri, Oct 10, 2008
If you are using a RadioLinx RLXIB-IHW radio with firmware revision 2.073 and set it to operate at 5GHz, there is a known issue in this version of firmware that causes the transmit power to drop to 0dB. The solution is to load an earlier... Read More
What firmware of RLXIB-IHW should I be using when WPA2/AES is used?
Viewed 1 times since Thu, Feb 5, 2009
Please make sure the RLXIB-IHW firmware version is at least IB3_441. Read More
What is the Mean Time Between Failure (MBTF) for the RLX2-IHA?
Viewed 1 times since Tue, May 5, 2015
The Mean Time Between Failure (MBTF) for the RLX2-IHA is 219,000 Hours. Read More
What kind of radio frequencies does ProSoft offer?
Viewed 1 times since Mon, Sep 28, 2015
ProSoft offers 900MHz, 2.4GHz, 5GHz, and Cellular (GSM/CDMA) frequency solutions Read More
Can I use the RLXIB-IHN radio with the newer RLX2 Industrial Hotspots?
Viewed 1 times since Fri, Sep 4, 2015
No. The RLXIB-IHN is not compatible with any of our other radios. It uses a specific software (Wireless N Discovery Tool) that none of our other radios use. Read More
What is the Mean Time Between Failure (MBTF) for the RLX2-IHNF?
Viewed 1 times since Tue, May 5, 2015
The Mean Time Between Failure (MBTF) for the RLX2-IHNF radio is 1,360,720 Hours. Read More
What is the Mean Time Between Failure (MBTF) for the RLX2-IHG?
Viewed 1 times since Tue, May 5, 2015
The Mean Time Between Failure (MBTF) for the RLX2-IHG is 560,640 Hours. Read More
What is the Mean Time Between Failure (MBTF) for the RLX2-IHW?
Viewed 1 times since Tue, May 5, 2015
The Mean Time Between Failure (MBTF) for the RLX2-IHW is 1,343,200 Hours. Read More
|
|