Home » Categories » Multiple Categories

Debug port connection parameters for Prosoft modules and gateways
Article Number: 6 | Rating: 3/5 from 4 votes | Last Updated: Tue, Jul 1, 2014 at 3:39 PM
Connect PC to module's debug / configuration port using a null-modem cable
  1. Start Hyperterminal, Putty or other comm program and use the following settings:
    • bits per second: 57,600
    • data bits: 8
    • parity: none
    • stop bits: 1
    • flow control: Xon/Xoff

  2. Once connected, press "?" to display debug menu.
Custom Fields
    Posted by: Technical Support - Tue, Nov 28, 2006 at 8:08 AM This article has been viewed 53018 times.
    Filed Under: 4000 / 5000 Series, MVI46 Series, MVI56 Series, MVI69 Series, MVI71 Series
    Attachments (0) Attachments
    There are no attachments for this article.
    Comments Comments
    There are no comments for this article. Be the first to post a comment.
    Icon Add Comment
    Name
    Email (Required, but not published)
    Comment
    Security Code Security Code
     
    Related Articles RSS Feed
    I need to connect multiple DF1 devices to a single serial port on an SLC or MicroLogix processor, is there a solution?
    Viewed 1 times since Tue, Nov 28, 2006
    I am using a ProSoft MVI46 solution and I am getting a Fault Message that says, "Specialty I/O Module in Slot x has not responded within the time limit." What can cause this?
    Viewed 1 times since Fri, Oct 31, 2008
    When the MVI71-MCM is connected using Side-Connect, can a Modbus Master device read and write to the same Modbus address in the module?
    Viewed 1 times since Tue, Nov 28, 2006
    What RSLogix 5000 function will indicate whether a Prosoft module is present and functioning in the ControlLogix chassis?
    Viewed 1 times since Tue, Nov 28, 2006
    My ControlNet network shows a maximum usage value of 99.61% when an MVI56-XXX or MVI56E-XXX is in the rack, why is this?
    Viewed 1 times since Fri, Oct 15, 2010
    Why am I unable to communicate with Wonderware from a 4xxx or 5xxx Series gateway in a full Duplex DF1 configuration
    Viewed 1 times since Tue, Nov 28, 2006
    Does the 4102 or 5102-MCM4-DFCM4 module have 4 Modbus ports and 4 DF1 ports (8 ports total)?
    Viewed 1 times since Tue, Nov 28, 2006
    What is the heat dissapation for MVI56, MVI56E, MVI69, MVI46 and MVI71 modules?
    Viewed 1 times since Thu, Jan 10, 2008
    Why am I unable to download a configuration file to a 4xxx or 5xxx Series gateway, and the Debug Port LED is on?
    Viewed 1 times since Fri, Jun 27, 2014
    Are the serial ports isolated on 4xxx or 5xxx Series Gateways
    Viewed 1 times since Mon, Jul 16, 2007
    • Icon SubscriberSubscribe to Article
    • Icon PrinterPrint Article
    • Icon EmailEmail Article to Friend
    • Icon PDFExport to PDF
    • Icon MS-WordExport to MS Word
    • Icon TwitterTweet This Article
    • Icon DiggDigg It
    • Icon StumbleuponStumble Upon
    • Icon de.icio.usDel.icio.us
    Article Rating (4 Votes)
    Rate this article
    Powered by PHPKB Knowledge Base Software