Contact Us
Home
Email
Follow Prosoft Technology on Twitter
Follow Prosoft Technology on Facebook
Follow Prosoft Technology on LinkedIn
Follow Prosoft Technology on YouTube
    • PROFINET Controller Module for ControlLogix®
    • EtherNet/IP™ to DH+ Gateway
    • Two-Port Building Automation Gateway
  • Solutions
    • Amusement
    • Automated Material Handling
    • Automotive
    • IIoT Solutions
    • Mining and Metals
    • Modernization
    • Oil and Gas Solutions
    • Secure Remote Connectivity
    • Water & Wastewater
  • Products
    • Remote Access
    • Rockwell Automation In-chassis
    • Gateways
    • Industrial Wireless
    • ProSoft Software
  • Services & Support
    • Knowledge Base
    • Regional Technical Support
    • Legacy Products
    • Training
    • Return Material Instructions
    • Literature
  • News & Events
    • ProSoft Insights (Blog)
    • Podcast
      • Knowledge Base / Gateways / AN-X / AN-X2 / AN-X2-AB-DHRIO

      DH+

      Search KB

      Categories

      • Gateways
        • ProLinx 4000/5000
        • PLX8x Gateways
        • QuickServer
        • PLX31/32 Gateways
        • PLX35 Gateways
        • AN-X / AN-X2
          • AN-X
          • AN-X(2)-GENI
          • AN-X-AMX
          • AN-X2-AB-DHRIO
            • RIO HMI
            • RIO DRV
            • RIO Scanner
            • DH+
        • PLX51 Gateways
      • Rockwell In-chassis
      • Schneider In-chassis
      • Wireless
      • Accessories
      • Protocols
      • Software
      • Legacy Products
      • Certifications
      • Technical Support
      • Miscellaneous

      Browse Categories

      MicroLogix 1400 MSG commands with AN-X(2)-AB-DHRIO in DH+ mode

      EtherNet/IP Message sample using a MicroLogix 1400 through a AN-X(2)-AB-DHRIO, to communicate with a processor on the DH+ network....

      Read more

      ControlLogix, CompactLogix, and SLC Message Samples through the AN-X(2) DH+ gateway

      The attached document contains both read and write message samples from a ControlLogix, CompactLogix, and SLC 5/05 processors to an SLC 5/04s and PLC5 processor on a DH+ network through the DH+ bridge gateway....

      Read more

      What driver should be used in RSLinx Classic to browse or get data from PLC5 or SLC controllers on a DH+ network?

      The best driver to use in RSLinx Classic is the Ethernet Devices driver.  Specify the IP Address of the AN-X(2)-AB-DHRIO gateway in the driver configuration.  The gateway emulates  a 4 slot ControlLogix chassis with an ethernet module and a DH+ bridge module in the...

      Read more

      What OPC Servers will work with the AN-X(2)-AB-DHRIO gateway running the DH+ firmware?

      There are several OPC servers that have been tested or are known to work through the AN-X(2)-AB-DHRIO running the DH+ bridge firmware: RSLinx Classic using the Ethernet Devices driver Wonderware using the DASABCIP driverKepware using the ControlLogix Ethernet driverAdditional OPC...

      Read more

      What are common things that prevent reliable DH+ communications on the AN-X(2)-AB-DHRIO gateway running the DH+ Bridge FW?

      If the NS or NET LED is not solid green then check the recommendations below: 1) For networks running at 57k6 or 115k2 bauds it is necessary to have 150 ohm resistors on each end of the network (for 230k4 use 82 ohm resistors) 2) Ensure that at least 10' or 3 meters of cable is u...

      Read more

      How can I use an AN-X2-AB-DHRIO to allow a SLC5/04 on DH+ to talk to a Panel View Plus on EtherNet/IP

      There are currently special restrictions on communicating with a SLC5/04 via DH+ with a Panel View Plus using EtherNet/IP through our AN-X2-AB-DHRIO, please see the attached tech-note for full details....

      Read more